3 Best Ways to Remove Water from iPhone Speaker

Water, moisture, and technology don’t always get along, so seeing your expensive iPhone fall into the sink, bath, or any body of water can be heartbreaking. Today’s phones are much more durable than in the past, so not all is lost. Learn how to remove water from iPhone speakers.

There are several options for getting water splashes out of the speaker. They all work in the same way. The water is displaced by a precise frequency sound broadcast through the speaker.

You can use the Siri Water Eject shortcut, a third party app, or website to push water out of the speaker. In this article, I will describe the best ways to remove water from an iPhone speaker.

Check if iPhone is water or dust resistant?

An ingress protection code, sometimes referred to as an IP rating, is used to rate the water resistance of phones. The IP rating of a device refers to its ability to withstand hard and liquid attacks. In the event of water damage, the warranty may not apply.

• There are two digits in the IP rating. The former refers to dust resistance, and the latter refers to water resistance, especially water resistance.
• If an iPhone is rated IP68, it can withstand solid objects and liquids.
• The IP68 class belongs to the popular iPhone 13 and Samsung Galaxy S21 devices.
• While IP ratings indicate how waterproof a phone is, swimming with phones can put you in danger.
• Oceans and pools contain salt, which can corrode your phone and force you to replace it.

What to do if your iPhone gets wet?

• Get your iPhone out of the water as soon as possible.
• The iPhone must not be connected. Unplug it if it’s already plugged in (very carefully).
• It should not be enabled. As a result, short circuits may occur.
• Take your wet iPhone out of its case, if it has one. Take out the SIM card as well. In these nooks and crannies, water can stand for a long time.
• Wipe liquid off anything; You can use a soft towel or cloth.
• Clean ports and connectors, turn iPhone over and shake it.
• Turn off your iPhone.

What happens if the phone falls into water?

When the phone is submerged in water, liquid fills the port and speaker. Water will enter the circuits of non-waterproof devices, causing corrosion of circuits, coils and resistors if no action is taken. It may also take time to break down weak components on a water-damaged phone, so the effect may not be immediate.

Water resistance is standard on all iPhone models. In accordance with IEC 60529, iPhone 7, mini, 8, iPhone SE, pro max, Xs Max, Plus, X, XR, and SE are IP67 rated for submersion up to one meter for up to 30 minutes.

iPhone XS and newer models are IP68 rated, allowing them to stay underwater for up to 30 minutes at a depth of two, four, or six meters, depending on the model.

Best Ways to Remove Water from iPhone Speakers

1. Use the Sonic app to remove water from your iPhone speaker
2. Automatically remove water from your speakers
3. Use the Siri Water Eject shortcut to remove water from your iPhone speaker

1. Use Sonic app to remove water from iPhone speaker

The Sonic app, which has a V in the App Store, has been updated for iOS 14 and works great on iOS 15. It is compatible with any iPhone running iOS 13 or later and any iPad running iPad 13.

Several in-app purchases are available, but they are not required for the main features of the app. You can pay to remove ads, change signal patterns, and save frequently used frequencies. All this is not required for the ejection of water.

Like some water removal apps, Sonic uses low frequency tones to expel water from speaker cabinets. Water Lock on the Apple Watch uses a “series of tones”to clear the device of water, but Apple doesn’t specify which low-frequency sound waves use the sound waves.

• After opening the Sonic app, tap the water drop icon in the center of the screen to remove water from your iPhone speakers.
• Sonic will immediately play a tone at the appropriate audio frequency, and you’ll need to turn up the volume on your iPhone to get enough vibrations to shake off the water.
• Lay your iPhone, along with the speakers, on a clean, absorbent, lint-free cloth to catch any drips.
• Small drops of water should come out of the speaker grilles depending on the amount of water.
• Some may even emerge from the front speaker near the earpiece.
• Even if you don’t see the water drain, your iPhone should sound normal again after a few minutes.
• To turn off the sound, tap the water drop icon again.
• As long as the water drop icon plays the tone, the frequency displayed on the screen is not affected.
• Whether the Sonic output is 440Hz, 1080Hz, or another frequency, tapping the water drop to play will play the same sound on your iPhone.
• Check the cable to remove water from the iPhone speaker.

2. Automatically remove water from your speakers

You can also remove water from iPhone speakers using a different frequency. Adjust the frequency manually instead of using the water drop icon.

• To decrease or increase the frequency, use the minus (–) and (+) icons, or swipe up or down the screen at a faster rate.
• I’ve seen a lot of references to 165Hz online, so somewhere between 150 and 200Hz is a good place to start.
• When you’re ready, turn up the volume and press the Play button.
• Vibrating pressure and displacement sound waves will shake the water when the frequency is set to the optimum level.
• Use an absorbent, lint-free towel to catch the drops, just like the water drop method.
• Check if your cable is leaking water from the iPhone speaker.

3. Use Siri Water Eject shortcut to remove water from iPhone speaker

Water Eject is a Siri shortcut that you can use if you have Siri shortcuts downloaded on your iPhone. It works just like the Sonic app. It makes a sound that instantly pushes water out of the speaker grille.

• If you haven’t already, download the Shortcuts app from the App Store.
• Once the shortcut is installed, get the shortcut and tap on the shortcut icon in the Shortcuts app to launch it.
• After that, go to “My Shortcuts”and tap it. Then, to execute the shortcut, click it.
• Start the water ejection process by pressing the Start Water Ejection button. Make sure your iPhone’s volume is turned up.
• Check if your cable is leaking water from the iPhone speaker.

Conclusion

Even though modern iPhones (iPhone 7 and later) are IP67 and IP68 water resistant, accidents do happen. Water can cause more problems with your phone than you think.

Sometimes it is not possible to remove water from the inside of an iPhone. If so, fill a bowl with packets of silica and place your iPhone speakers inside the bowl to dry your wet iPhone.

FAQ

How to remove water from phone speaker?

Make sure the phone is positioned so that the damaged speaker is pointing down. Alternatively, you can bury your phone in uncooked rice for at least 24 hours. Because rice tends to suck up all the liquid around it, this method is great for draining water from your phone’s speaker.

How to remove water from iPhone speaker?

To increase the volume, use the volume up button. Hold your finger on the water drop icon. Swipe anywhere on the screen to change the frequency to 160 and 200. Repeat the above procedure until no more water drops from the speaker grille.

Will water come out of the iPhone speaker?

Despite the fact that modern iPhones are waterproof, there is no official means to remove water from the speaker grills, unlike the Apple Watch. If the water is not removed, it will drown out the sound and cause significant damage.

How to dry your phone quickly?

“If a desiccant is applied, silica gel, couscous and quick rice are rated as the best options.”After using the rice method, six out of nine phones were able to turn on, and two more were able to extract most of the data from the phone.